Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
Are you trying to locate know-how about How to Install a Bathtub?
Installing a tub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is conveniently obtainable, the task can move immediately; if you have to open a wall surface to eliminate the old tub and position the brand-new tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to move out the old tub and set in the brand-new one. Ensure you have actually qualified yourself for the task and also fit attempting it. Rather than employing a specialist to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you may require an expert plumber to make tube connections.
This article will help you mount a brand-new tub in your restroom if you have already bought a new bathtub and do not require to change the plan of your previous water pipes.
Your tools as well as product checklist need to consist of the following:
Getting ready for the Setup
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be quite problematic due to the restricted gain access to that is often the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. When the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Using the two wooden boards under its feet, put the bathtub in the required position. The wood boards are practical in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the bath tub till the level checks out level.
To mount faucets, fit the bottom of the outermost flexible tap adapter to the proper supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the water and examine all joints and new pipework for leaks as well as tighten them if required. Load the bathtub and likewise check the overflow outlet and the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the tub ought to wait till the tub has been utilized a minimum of when as this will certainly settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing opening in the bath/basin making sure that the washing machines are in location in between the tap and the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous type should be connected to the faucet ends first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall between the bath and the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealant can split relatively very early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you really like reading up on How to Install a Bathtub Yourself? Place feedback further down. We will be interested to know your thinking about this blog. In hopes that you visit us again soon. I beg you take the time to promote this article if you enjoyed reading it. Many thanks for your time. Visit us again soon.
Call, we respond! Report this page